MACHINE SIZES: 4X4, 4X8, 5X5, 5X10, 6X12

• Powermax 45XP, Air, 45 Amps

• Powermax 65, Air, 65 Amps

• Powermax 85, Air, 85 Amps

3 Phase Only

• Powermax 105, Air, 105 Amps (208V)

• Powermax125, Air, 125 Amps (480V)

• Cutmaster A40 45XP, Air, 40 Amps

• Cutmaster A60, Air, 60 Amps

• Cutmaster A80, Air, 80 Amps

• Powermax 120, Air, 120 Amps

• Slim Linear Actuator Design (Increasing Cutting Area)

• Internal Wiring Harness Sub Assembly (For easy diagnosis and repair)

• Integrated Multi-Process Pneumatic Actuator Scribe and Marker

• Protective Front Enclosure (Covering linear components and Pneumatic cylinders)

• Rear Enclosure Protection (Covering Motor Reduction System and Pneumatic Assembly)

• Enclosed Cable Carrier (Assisting with management of collision detection wiring and pneumatic hoses)

Z-AXIS FULLY INTEGRATED MULTI-PROCESS

FULLY WELDED STEEL FRAME

• Fully Welded Tube Frame

• Extremely Rigid To Counteract Vibrations and Inertia

• Dropped Side Rail Design for 3 Side Material Loading

• 4" Deep Water Pan

• 4" Diameter Leveling Feet With Rubber Pads (3/4-11 Thread)

• Machined and welded gear rack mounting surface (Easily replaceable)

• Extended Frame Along Y-Axis For Gantry Parking Zone 

• Adjustable PC station Leg Mounting

PNEUMATIC RACK SUB-ASSEMBLY

• Pneumatic Rack Sub Assembly (Easy Diagnosis and Repair)

• Dual Low pressure Air Regulators (Allowing For Easy Adjustment of Scribe and Marker Pressure)

• 3 Pneumatic Solenoids With Quick Connect 1/4" Hose Fittings 

• 4 Bulkhead Quick Connect 1/4" Hose Fittings (For Air Inlet and Outlets)

• Isolation Of Complete Control Assembly

• Allows for Dual Actuation of 2 different tools (Standard Tools are Scribe & Sharpie Marker)

COLLISION DETECTION HEAD-ASSEMBLY 

• 2 Axis Squaring For Torch Setup (Referred To In Hypertherm Manual)

• Dual Collision Proximity Sensors (Allowing For Program Stop Within 2 Degrees Out Of Alignment)

• Front Floating Proximity Sensor (Secondary Touch Off Option If Ohmic Fails To Sense Material)

• Indexing Cones Design (Provides Torch  Relocating of True Position)

• Unique Hexagon Geometry (Unlike Competitors Our Collision Detection Head Is Designed And Manufactured By Squickmon's in the USA)

• Integrated Positive Z-Axis Homing (No Material Loading Required For Homing)

TABLE CONSTRUCTION AND SIZE OPTIONS 

• Machined .625" T6 6061 Aluminum Gantry Side Plates

• Ground 4" Wide X-Axis Linear Rail System & Machined Roller Cassettes

• Case Hardened Y-Axis Linear Rail System & 8 Roller Bearing Cassette Per Gantry Side

• 3" Slat Offset (Helps with Tipped parts when Cutting)

• 7" Gantry Clearance (Beneficial When Cutting Large Part profiles, Beams, and Tubing)

• 14g Steel Gantry Enclosure Protection (Guards Motors And Reduction Assemblies From Impact)

• Adjustment for Gantry Squaring and Homing Switch Positions

• Heavy .125" Wall Tubing and Welded Steel Pan Frame Construction

• All Maverick Series Systems are Sized To Fit A Full Size Sheet Relative To Their Designated Machine Size Plus 1-2" Oversized For Cutting Area (Example 4x8 Machine has a minimum of 49"x97" Cutting Area)